IST-53

IST-53BT-2 Axle IST-53BT-3 Axle IST-53BT-4 Axle

Load Height Adjustable
Trailer Neck Schnabel Trailer Half Schnabel Trailer Expandable Schnabel Trailer Heavy Haul Trailers Dolly Jeep Financing Warranty Dealer About Us See Us In Action Contact Us

IST New Generation "2010" Wind Turbine Blade Trailer

Model:"The Blade" IST-53' BT "2010"

The IST- 53' BT 2010 Model Blade trailer requires No Forklift, No Crane or Equipment to Extend or Collapse!!! The new dual purpose neck adjusts to desired load height allowing you to accommodate for the new industry generation of wind turbine blades. This will allow the operator to lower the load height for bridges or raising the height for rough job sites or railroad tracks. On top of everything else you can now load the pilot car. Grab your remote, lower front of trailer, load car, raise trailer with remote, back truck underneath, hook up and GO! Good News for All!! This NEW neck will retrofit any brand of Blade Trailer!! And always remember that 37 degree turning radius that we boast of. This IST blade trailer is ingenuity at it's very finest. It's been on the leading edge and one of the most proven blade trailers in the field today.

Highlights of "The Blade" Model IST-53' BT "2010 "

Specifications	Model Blade IST- 53’ BT 2010
Capacity	70,000 lbs.
Weight	27,500 lbs.
Overall Length	128’ + 15' Non Load bearing extension, Total length 143'
Closed Length	53’
Overall Width	102”
King Pin Height	48”
Gooseneck Swing Clearance	75”
2” SAE King Pin	Standard
Main Box Beams	3 sections, adjustable length, 33" spacing along 1st & 2nd beam/ T1 steel flanges, built in stops
Landing Gear	Hydraulic landing gear
Suspension	Air Ride
Axles	(2) 25,000 lbs.
Wheels	(9) Aluminium rims, 17.5” x 6.75” HP 8 lug wheels
Hubs	8 bolt " Budds" outboard hub piloted
Tires	(9) 245-70-17.5 (includes spare tire)
Tire Load Range	Load Range J
Spare Tire & Mount	Standard
Brakes	Airbrakes 12 1/4" x 7 1/2" ABS, auto slack adjuster
Fenders	(2) reinforced weight bearing on Gooseneck/(4) on Chassis/Standard
Mud Flaps	(4) Standard
Wiring	Sealed modular harness/Standard
Shock Mounted Lighting	LED/Standard, (2) removable strobe lights (360 degree)/Standard
Connector	7 pin round
Turn Table Hyd Steering	Gas Pony Motor w/electric back-up system, start & stop from pilot car, 37 degree turning radius/Standard
Remote System	All functions wireless remote (Start-Stop)
Bolster	(2) Permanently mounted/Standard, w/(8) D-Rings and (2) J-Hooks per side
Taco/Blade Tip Holder	(2) Removable/Standard, w/(6) D-Rings and (2) J-Hooks per side
Tool Box	(1) Standard
Flag Holders	(4) Standard
Load Bunk	(2) Removable/Standard, w/(6) D-Rings w/ (2) J-Hooks per side, ratcheting adjustment
Neck Ramps	(2) Front ramps w/traction plates/Standard, (2) Pilot vehicle placement ramps w/traction plates/Standard
Extension	15' Non-Load bearing/Standard
Paint Finish	"Black" Dupont Imron Paint/Standard

Dealer:
Check back soon for dealer info.

Lower Blade heights for bridges with New purpose neck!!!!!

Raise neck to travel easier in poor site conditions or to clear railroad tracks

Hose wrap, mounted tool box, & side mounted taco

Side mounted taco, pony motor start & stop from pilot car, & spare tire

Low profile neck comes standard with LED lights, front bolster, 2 fenders and landing gear system

Sharp turning radius of 37 degrees